Well, if your Bush TV not turning on, don’t panic and continue reading this solution guide!
We know how frustrating it must be when your TV is not turning on, and you have absolutely no idea what’s causing this problem.
If your Bush TV is not turning on, there may be something wrong with the TV remote, wall outlet or power connection.
If Bush TV is not turning on, unplug your TV, then hold the power button for 15 seconds, and thoroughly inspect the wiring, Bush TV power port, and test the hardware.
Let’s quickly dig deeper to unwrap more information!
Why is My Bush TV Not Turning On?
Any TV, not only Bush TV, won’t turn on when the remote is not responding or when the device’s power supply is insufficient.
There are many possible factors that can prevent the Bush TV from turning on, so let’s explore the possibilities to acquire a better orientation for troubleshooting!
Here’s everything that can prevent your Bush TV from turning on:
There are many causes, so we’ll exclude a potential hardware malfunction for now and attempt to address each of the causes.
So, without any hassle, let’s continue with the troubleshooting…
How to Fix When Bush TV Not Turning On?
Tip: Follow the steps in a consecutive order!
1. Inspect the Power Connections
The first thing you must do is run a quick inspection on your Bush TV power connection at both the TV and the power outlet.
If any of these port connections are loose or disconnected, you must securely connect them to restore the functionality of your Bush TV.
Here is how to inspect the power connections of your TV:
- Unplug the power wire of the Bush TV from the wall outlet.
- Next, disconnect the power cable from the television’s back.
- Check the full length of the cable for any defect or damage.
- Clean the connectors and Bush TV power port from any dust.
- Firmly reconnect the power wire back to the TV and socket.
Make sure to directly plug your Bush TV into the outlet instead of plugging through any surge protectors, extension cables or smart plugs.
This will guarantee constant power income to the TV and prevent startup failures.
Tip: Try turning on the Bush TV using the physical power button and bypassing the remote!
2. Soft Reset Your Bush TV
Sometimes, a simple reset to your device can help resolve issues with your non-responsive TV.
This is an excellent workaround to perform early into the guide, which will clear the Bush TV flashing red light, and all temporary software or internal glitches and allow your TV to turn on!
Here is how to power reset your Bush TV in easy steps:
- First, disconnect your TV from the wall socket.
- Then, locate the in-built Power button on the TV.
- Push and hold down the button for 15 seconds.
- Release the button and wait for 3 to 5 minutes.
- Lastly, plug your Bush TV back into the socket.
After you are done, point your TV remote towards your TV and push the “Power” button on the remote.
In case your TV is still blinking in red and not turning on, then continue reading ahead.
3. Check the Remote Control
There is a good possibility that your Bush TV remote control is malfunctioning, and that’s why it is unable to communicate with your TV to turn it on.
In this case, you have to give a good clean to the IR sensors’ “red bulbs” on your devices, then try turning on your TV using the TV remote.
Here are the simple steps to check the remote control:
- First, unplug your unit from the wall socket.
- Locate the IR sensor on top of the remote.
- Properly clean the sensor with a soft cloth.
- Next, locate the IR sensor on your Bush TV.
- Clean the sensor using a soft and clean cloth.
- Then, plug your TV back into the wall socket.
- Point your remote in line of sight to the TV.
- Press the “Power” button on the Bush remote.
Tip: Test turning on the Bush TV by stating right in front of the display!
4. Check for the Standby Mode
If your TV Bush TV not turning on red light flashing, this means the Bush TV is stuck in standby mode due to poor ventilation, power supply or software issues.
In such a case, you must wake up your TV from the standby mode by pressing the built-in power button from the TV panel.
Here is how to exit Standby Mode if your Bush TV is frozen:
- First, unplug your Bush TV from the electrical outlet.
- Locate the Power or Standby button on the Bush TV.
- Press and hold the “Standby” button for 10 seconds.
- While holding the standby button, plug your TV back.
- If the Bush TV doesn’t turn on, press the Power button.
After you are done, point your TV remote directly toward the IR sensor on your Bush TV and try turning it on.
If the same problem continues, continue reading for further solutions ahead…
5. Replace the Remote Batteries!
If everything is in working condition, but your Bush TV won’t turn on, faulty or dead batteries in your remote can be the culprit.
Simply install a fresh set of high-quality batteries in your Bush TV remote and check if your problem is resolved.
- The Bush TV remote control uses 2 x AAA alkaline batteries!
When replacing the batteries, you must verify that the compartment’s polarity springs are not bent, twisted or missing.
Also, you must clean any dust accumulation, which may affect the battery’s contact and eventually prevent the Bush TV remote control from working correctly.
Tip: Use only brand-new batteries for your remote!
6. Verify the Bush TV Wall Outlet
There is a good possibility that your TV outlet is not providing sufficient voltage, which is why the TV is not turning on.
To check if that’s the case, simply try plugging a different electronic device into the TV outlet and check if the device is correctly functioning.
If you’re unsure exactly what to do, follow the steps below:
- Unplug your Bush TV from the outlet.
- Get access to a phone charger or lamp.
- Plug a different device into the outlet.
- Check if your new device is functioning.
When you’re using a lamp or a wired bulb, you can immediately tell whether the voltage from an outlet is fluctuating or is very weak.
If you detect a wall outlet problem, and there was no recent power outage, then we recommend calling a professional for an inspection of the power outlet.
Warning: Avoid using a defective power outlet in your home!
7. Switch to a Different Power Source!
If you are sure your TV outlet is working fine, but your Bush TV is still not turning on, try using a different wall outlet from a different fuse.
This step is crucial because, over time, the fuses on your primary circuit may lose functionality and stop providing sufficient power supply voltage.
All you need to do is disconnect your Bush TV from the original socket and directly plug the TV into a different wall outlet, preferably in a different circuit.
Make sure while you are turning your TV on, there are no physical obstructions between your TV and the remote’s infrared blaster.
Reminder: Avoid using any extension cords, smart plugs or surge protectors!
Need More Help?
If you have correctly tried each step, but your Bush TV is still not turning on, there is something wrong with the TV itself.
It can be hardware or internal damage, such as faulty circuit boards or capacitors, so you may need to take your TV for repair replacement. Best of luck!
Quick Recap:
If you don’t know why your Bush TV not turning on, first, soft reset the TV and clean the IR sensors on the remote and on the Bush TV.
If the issue persists, install fresh batteries in the remote control, look for interfering devices or plug your TV into a different outlet.
Follow us for Bush TV guides!
