Hunter Ceiling Fan Runs Slow On Highest Setting? – Fix Guide

Wondering why Hunter ceiling fan runs slow on highest setting? Let’s find out together!

Although fans are the most common appliance in everyone’s home, it causes many troubles, especially when it runs so slowly even in the highest temperature settings.

The Hunter ceiling fan is no expectation and the causes remain the same for almost all brands of fans!

The Hunter ceiling fans run slowly on the highest settings because of a faulty capacitor,  loss of lubrication, defective fan motor, or insufficient power voltage.

The solution only requires inspecting the entire setup to identify and solve the problem in minutes!

Next, let’s talk about the most effective and easy ways to fix the slow fan problem!

Hunter Ceiling Fan Slow on High Setting – 1 Minute Fix!

If your ceiling fan runs slowly even on the highest settings, there may be any defective part causing this issue.

As it is clear, maintaining your appliance properly and replacing any worn-out or malfunctioning components is crucial to prevent you from experiencing such issues.

Let’s go to troubleshoot the Hunter ceiling fan!

Solution #1 Test Power Voltage

The first and most common cause of a slow fan is insufficient to power voltage.

The fan requires a sufficient voltage to run appropriately according to the high-speed settings and when it can’t get enough power, the fan won’t go any faster.

Test the power voltage of the Hunter fan’s electric board using a Multimeter and compare your findings to the manual’s default values.

Also, check your home voltage supply (AC Line) and also make sure that the circuit breaker and electrical board are working fine.

In addition, inspect whether the other appliances are working fine or not, which would suggest if the problem is related to the Hunter fan only or not.

Note: Any fluctuations in your AC line might impact ALL of your electronic appliances.

Solution #2 Inspect The Wiring

Over time, the wire connection deteriorates, which causes the insulation between components to become weak.

Your Hunter ceiling fan might run slowly at high settings due to loose wires or damaged electrical connections, which could cause the power to not flow properly.

To troubleshoot the Hunter ceiling fan wiring follow the steps below:

1. Turn off the power to the Hunter fan! 
2. Remove the fan base from the ceiling. 
3. This will provide you with access to the wires.
4. Carefully check for loose or damaged wires. 
5. Simply tighten ALL wires and turn on the power.

It’s not safe to interact with the wires of the fan if you’re not familiar with the electrical installation.

In case you detect any defective wire, then call an electrician for the repair!

Solution #3 Check The Speed Controller!

Another possibility that has a direct influence on the fan speed is the fan reverse switch or remote control.

We can use them to control the fan speed, but maybe your fan remote or the switch is defective or not working because of any other factor such as heat, or due to long use.

Simply try to adjust the settings on the fan remote to test the speed controller and see if the fan speed changes.

If there is no change, then the remote control is definitely defective, and you must get a replacement from Hunter.

Note: If your fan has any reverse switch, then make sure it is not set to a middle position!

Solution #4 Apply More Lubrication

The Hunter ceiling fan’s fan motor already has a built-in lubricating motor that maintains the motor lubrication for a long time.

Hence, there is really no need to apply any lubricating oil to its components on a monthly or even yearly basis.

However, if you have been using the Hunter fan for a long time and have not given the device any maintenance, the poor operation should be expected.

The problem might not be the motor but also the fan, and when it’s too dry it would run slower even on the highest setting.

Note: If lubricating the fan components does not increase your fan speed, try another solution!

Solution #5 Check The Fan Blades

The balancing and alignment of the fan blades are one of the most important factors.

The blades rotate around the fan’s main axis and if they settle properly at their place, they won’t move properly whether you have set the speed to high or low.

• Did you previously remove the blades of your Hunter fan? 

If yes, there is a high chance that the blades are now not balanced, which is why the Hunter fan not spinning fast enough, even on the highest setting.

To check the blades on your fan, simply look at the blades and carefully check if there is any imbalance that you will see.

Make sure that the blades are firmly attached and the space between each wing is equal because any imbalance will prevent the fan from spinning fast.

Note: Improper balancing of fan blades can also lead to short-circuiting or overheating of the appliance!

Solution #6 Check The Fan Pull Chain

The Pull Chain in the fan will allow it to run according to the speed settings. There is a chance that the pull chain in your fan is worn out or not aligned properly.

Perhaps this is why your fan runs slow even though you have set the settings to high.

Here is how you can check the Hunter fan pull chain:

1. Turn off the ceiling fan Power Supply.
2. Then unscrew the Fan Base.
3. Remove the Metal Collar from the fan.
4. Take out the Pull Chain switch from the fan.
5. Inspect the Pull Chain Switch for any damage or defect.
6. If you found any, then set up a new pull chain switch into the fan. 
7. Otherwise, install back the previous one.
8. Next, take the Pull Chain Switch and place it into the fan.
9. Make sure that the pull chain switch is balanced properly.
10. Then, install back the other parts to close the fan assembly.

If the pull chain switch doesn’t work, then you need to test your fan motor!

Solution #7 Replace The Fan Capacitor!

The Hunter fan capacitor is one of the most frequently replaced components in the device because it supplies power to the fan motor and controls the fan speed.

The capacitor is always engaged and working, and after a long time of usage, the piece typically gets faulty.

If one thing is guaranteed is that when the capacitor is not working your hunter ceiling fan runs slow on the highest setting.

In the worst cases, the capacitor is completely dead and the ceiling fan won’t even turn on. However, replacing the capacitor will fix the issue!

Here is how to replace the capacitor in the Hunter ceiling fan:

1. Turn off the fan Power Supply.
2. Disconnect the light kit from the fan to get access to housing.
3. Then, unscrew the fan base from the ceiling and place it down.
4. Unscrew the grommet from the fan to free the switch from the wires.

• Use any of the pointed tools to release the purple, brown, and gray wires from the switch, and make sure to note down the wire’s slot number.

5. Then, cut down the red and gray wire from the wire stripper.
6. Hold the old capacitor and take that out.
7. Set up a new capacitor and strip the previously cut wires.
8. Then connect the capacitor and other striped wires,
9. Secure the wires with any electrical tape or just tape.
10. Next simply the gray, purple, and brown wires to the capacitor.
11. Lastly, assemble all other components accordingly. 

In case you’re wondering where to acquire a replacement capacitor for your Hunter ceiling fan, we recommend getting CNCYEAH Ceiling Fan Capacitor.

Amazon’s choice and proven by the users, this capacitor is easy to replace and will solve the problem without a doubt.

Quick Recap:

Whenever your Hunter ceiling fan runs slow on highest settings, you need to check the AC line, circuit breaker, and fan switch.

If you can’t identify the issue, you’ll need to start replacing suspected components such as capacitors, fan motors, or pull chains! 

Check out our blog for more helpful troubleshooting guides!