Why Does Dyson Airwrap Keeps Turning Off?

Wondering why does the Dyson Airwrap keeps turning off? The Dyson Airwrap is an amazing appliance if it works as intended.

However, sometimes it presents issues.

The Dyson Airwrap keeps turning off because of some issues with the components. A malfunction occurs on the cord, power plug, or air filter. Alternatively, the wattage is not correct.

The guide below will walk you through all the fixing steps.

After that, you can analyze what is happening with your Dyson Airwrap and then grab the tools to fix it.

It is not hard at all. 

Dyson Airwrap Keeps Turning Off – Common Reasons

Why does my Dyson Airwrap keep turning off? Before we show you all the fixing possibilities, we must debate why your appliance keeps turning off.

As with any electrical device, a certain range of issues affects it. Below you can check the most common reasons behind your Dyson Airwrap shutting down unexpectedly.

#1. Damaged Cord/Plug

Look for evidence of wear and tear or other damage to the power cord.

#2. Faulty Power Supply

The home’s power supply, including the circuit breaker, wall outlets, and other components, may be at the root of the problem.

#3. Incorrect Voltage

Dyson Airwrap will stop immediately if the voltage is wrong.

#4. Incorrectly Connected Attachments

Before using the Dyson Airwrap, its various parts must be properly fastened.

#5. Overheating

Many devices nowadays will turn off when they heat up to a certain point. That prevents further damage and also protects the users.

#6. Clogged Air Filter

To be functional, the Dyson Airwrap does require an air filter. When it is clogged, malfunctioning will happen, such as unexpected turning off.

How To Fix Dyson Airwrap When It Keeps Turning Off

You can apply many solutions when you see your Dyson Airwrap turning off. Below we will list plenty of solutions that apply to different issues.

You must check the common reasons behind the unexpected shutdowns. After the correct diagnosis, you can proceed to fix it.

Solution #1: Fix The Power Cord

First, you must buy a crimping and stripping tool set. It is usually available for around twenty dollars.

Then follow the steps:

1. Use a box cutter to remove the thick exterior insulator.
2. Expose the fiberglass insulation on both sides of the break
3. Cut a bit of the cable. 
4. Remove the insulation from the smaller wires underneath.
5. Remove about one inch of insulation from each end of each internal wire using the stripping tool.
6. Twist the exposed copper so that the strands become twisted

This is very important: you will want higher power application crimps to connect the wires of this 1300W device. 

Depending on your toolkit, you may require higher-power application crimps to join the wires. The 50 amp rating should suffice. 

Here are the final steps:

1. Separately crimp each wire to its counterpart on the other end of the cable (same color to the same color)
2. Wrap each crimp individually in electrical tape to protect any exposed copper or metal.
3. Tape the whole cable together using electrical tape to maintain its integrity.

Solution #2: Replace The Power Plug

Replacing a damaged power plug can be a straightforward process. Still, it’s important to take safety precautions and follow the instructions carefully to avoid injury or damage to the device.

Here’s a general guide on how to replace a damaged power plug.

Gather the necessary tools and materials: 

• A new power plug
• A screwdriver (either a Phillips or flathead, depending on the type of screws on the plug)
• Wire stripper.

Unplug the device: Before you begin, ensure that the device is unplugged from the outlet and that it's safe to work on.

1. Use the screwdriver to loosen and remove the screws holding the power plug. 
2. Pull the old power plug out.
3. Use the wire stripper to remove a small section of the insulation from the end of each wire. 
4. Connect the wires to the new power plug: 
5. Use a screwdriver to secure the wires in place.
6. Attach the plug to the device. 
7. Use the screwdriver to tighten the screws that hold the power plug in place.

Once you’ve finished replacing the power plug, plug the device in and test it to ensure it’s working properly. 

If the device doesn’t turn on, there may be an issue with the wiring or the power plug. In this case, you may need to seek the help of a professional electrician.

Note: The wire colors may vary depending on the device and the power plug you use. Refer to the manufacturer's instructions or a wiring diagram to determine which wire goes where. 

Solution #3: Adjust The Voltage

Be sure that the power settings on your device are adjusted as directed by the manufacturer.

To avoid damaging your home’s electrical system, ensure the voltage setting is the same as your home’s power source.

To ensure that the voltage is correct on Dyson Airwrap, follow these guidelines:

• Ensure that the outlet you use is properly grounded and has the correct voltage.
• The Dyson Airwrap requires a voltage of 110-240V.
• If you are using an extension cord or power strip, make sure that it is rated for the wattage of the Dyson Airwrap and is in good condition.

Suppose you are still having issues with the voltage on your Dyson Airwrap. In that case, it is best to contact Dyson customer service for assistance.

They can provide further guidance and help troubleshoot any problems you may be experiencing.

Solution #4: Clean The Air Filter

Cleaning the air filter on your Dyson Airwrap is an important maintenance task that can help improve the performance and lifespan of the device.

Here’s a guide on how to clean the air filter:

1. Turn off and unplug the Airwrap
2. Locate the air filter (the air filter is typically located in the back of the Airwrap, near the motor). 
3. Remove the air filter (This may involve pressing a release button or removing a screw)
4. Clean it using a brush or a can of compressed air. 
5. Once the air filter is clean and dry, you can put it back in place in the Airwrap. 
6. Make sure that it’s properly seated and secured in place.

Once you’ve finished cleaning and replacing the air filter, plug the Airwrap back in and test it to ensure it’s working properly. 

Suppose the device doesn’t turn on or seems to be functioning poorly even after the steps above.

Thus, there may be an issue with the air filter or another component. In this case, you may need to seek the help of a professional or contact Dyson customer support.

Note: If the air filter is very dirty, you may need to wash it using warm water and mild detergent. Make sure that the air filter is completely dry before replacing it.

Solution #5: Prevent Overheating

Overheating is troublesome as it can damage your appliances in the short and long term.

To prevent overheating in a Dyson Airwrap, you must follow these guidelines:

• Make sure the Airwrap is clean. Overheating can sometimes be caused by a build-up of dust or debris in the device.
• Avoid using the Airwrap for extended periods. If you need to style your hair for a long time, take breaks to allow the device to cool down.
• Use the lowest heat setting possible. The higher the heat setting, the more likely the Airwrap will overheat.
• Avoid using the Airwrap on wet hair. That can cause the device to overheat as it works harder to dry the hair.
• If the Airwrap starts to overheat, turn it off and allow it to cool down before continuing to use it.

What We Learned

What to do when the Dyson Airwrap keeps turning off? We understand that such a situation is very annoying. To solve that, you must inspect the electric parts. 

You might find out that the cord, the plug, or any other part is at fault. After that, you must follow the fixing steps as laid down above.