Aroeve Air Purifier Red Light? – (Easy Fix Guide)

It can be frustrating having your air purifier set up only to receive an error notification.

Whenever the Aroeve air purifier red light is blinking, it can either indicate an issue with the filtration system or the air quality.

To fix your Aroeve air purifier, start by power cycling your device and cleaning the air filters. If the issue persists, you must replace your filter with a brand-new one. 

Now that you have a general idea of the fixes, let’s first see how this problem can be caused:

Why Does My Aroeve Air Purifier Have a Red Light?

If you receive any light-coded signals from your air purifier, it indicates that action must be taken so normal operations continue.

The color coding for a red light is related to your Aroeve air purifier struggling to filter air due to an obstruction or depleted filter lifecycle.

Here are some common causes for Aroeve air purifier having a red light:

Now that you know about what causes the Aroeve red light notification, let’s jump into trying to fix it!

How to Fix Aroeve Air Purifier Red Light?

Tip: A red light can also indicate poor air quality in your room. 

1. Power Cycle Your Aroeve Purifier

Aroeve air purifiers are complex devices that rely on software to make split-second decisions and to gauge the air quality.

Sometimes, they can encounter an error that causes a sensor to malfunction and send a warning.

The fix to this issue is power cycling your device to clean its temporary memory. 

Here are the general steps to power cycle your Aroeve purifier:

1. Unplug the Aroeve air purifier from your power socket.
2. Wait for at least 30 seconds while the device discharges residual electricity.
3. Plug the Aroeve purifier back in.
4. Ensure you use a surge protector when plugging your Aroeve purifier.
5. Turn the Aroeve on to check the light status.

Note: If you experienced a power surge from a storm, your Aroeve could have suffered damage.

2. Clean Your Purifier Filters

To get your Aroeve air purifier’s red light reset or to stop blinking, it’s essential to check the filter.

If the filter gets clogged up due to filtering out small dust particles, it can impair its ability to process the air around it.

The exact steps to clean your Aroeve purifier filters can vary based on your device model and type. 

With that said, here is how to clean your Aroeve air purifier filters:

1. Turn off and unplug the Aroeve purifier from its power source. 
2. Open the filter compartment, usually accessed by pressing a switch.
3. Remove the pre-filter or the primary filter.
4. Clean the removable air filter by vacuuming the surface gently.
5. Before reinserting the filters, read on the next step, as it’s also vital.

Please note that some filters, like the HEPA filter, should NOT be washed or soaked with liquids.

If you are unsure what type of filter your Aroeve uses, consult the user manual first. 

Unless stated otherwise, you can wipe the filter with a warm towel or cloth to remove stuck dirt particles. It’s recommended to vacuum first and wash second.

Note: Don’t overuse harsh detergents or other household cleaning solutions to clean your filter.

3. Clean the Interior Area

The interior area of your Aroeve is the surface with which the filter comes in contact and is also a part of the device you should service regularly.

It’s vital that not only the air filter gets cleaned but also its surroundings.

Even if you insert a brand-new filter into a dirty compartment, it can still cause a red light warning.

The steps to clean the interior area are as follows: 

1. Unplug your Aroeve cleaner from the power outlet.
2. Open the air purifier front or back cover, depending on your model.
3. After removing the filter, get your vacuum cleaner and attach a soft brush end to it.
4. Gently remove all the dust from the fan blade, vents, or corners.
5. Reinsert the filter and close the compartment.
6. Turn the Aroeve air purifier back on and see if the red light is gone.

If the efficiency of your Aroeve is compromised since it’s overworking, your filter can get depleted quickly.

Note: Check your Aroeve user manual for exact steps to clean the interior area properly. 

4. Remove Any Obstructions

Air purifiers like the Aroeve require a good amount of space between them and any surroundings.

If you place your air purifier incorrectly, its efficiency in filtering air can significantly diminish.

It can also take in excessive dust and thus deplete its filters pre-maturely. 

Here are some tips to keep your Aroeve air purifier in an optimal position:

• Have at least 2 feet of clearance from walls or furniture to all sides of your Aroeve air purifier.
• If using a thick carpet, ensure the Aroeve filter is placed slightly above the ground level.
• Be careful of putting the air purifier near curtains as they can stick to the intake cover and cause overheating.

Note: If you have pets, place your Aroeve purifier in an elevated and hard-to-reach position.

5. Check Ambient Light Sensor

Many of the newer models of Aroeve air purifiers rely on sensors to give them vital information about the surrounding environment.

If a physical barrier obstructs some of these filters or the sensor is dirty, it could cause erroneous readings. To prevent this, you must ensure any sensors are not obstructed.

Here are the steps to ensure your ambient sensors are in working order:

1. Clean all of the Aroeve sensors you can find by using a soft cloth.
2. Ensure your sensors are not covered or obstructed by surrounding furniture.
3. Turn the cleaner on and off and check if the red light issue persists. 

Note: You can also configure the sensor's sensitivity if they are disproportionately activating.

6. Replace Your Filter 

If you have performed the steps above, but your Aroeve is still giving you a bad filter red light warning, it’s probably time to replace your filter.

You know you are getting the best air quality possible when you use a brand-new filter.

Regular air filter swapping is usually straightforward, but ensure you follow the proper steps for your exact model.

Here are the steps to replace your Aroeve air purifier filter:

1. Turn off the air purifier and access its filter compartment by removing the cover.
2. Remove any latches or slide the cover off, depending on your setup.
3. Remove the old filter gently and ensure the surrounding area is also clean.
4. Get the correct filter type for your system, and note if it’s a pre-filter, HEPA, or carbon filter type.
5. Insert the new filter until it snaps or locks into place, and close the filter compartment with its back cover.

After these steps, simply power on your Aroeve air purifier again and see if you still get the replacement filter light to flash.

If it’s still flashing after installing the new filter, perform the power cycling step again.

Note: If you are using a carbon-based filter, it's best to replace it rather than clean it.

Quick Recap

Thus, whenever the Aroeve air purifier’s red light keeps on blinking, an air filter check or change is due.

After you have replaced the filter, clean the internal area and ensure proper airflow and Aroeve purifier placement.

Lastly, seek further help from customer support to get specific steps for your Aroeve model.