How To Fix Points Of Light Remote Not Working?

The points of light remote not working and you’re looking for a quick solution?

Well, the issue could occur if the light projector is too far away from the remote or if you’re using the wrong battery.

Regardless of where the problem is coming from, here we will cover all causes that could prevent your light remote’s points from working.

To fix the non-working light remote points, make sure that you’re not using the projector outside during extreme weather conditions. Then you should inspect and power cycle the projector. If that doesn’t work, replace the battery and re-pair the remote.

Before we move on to troubleshooting, it is recommended to learn what could be causing the problem with your light remote.

Why Are Gemmy Points Of Light Remote Not Working?

If your light remote doesn’t seem to enable the gemmy points of your projector, then the fault could either be with your remote or the projector itself.

Here are some of the reasons that might be causing this issue with your light remote:

1. Distance Issue

Your remote has a certain range and if you over exceed it, the projector won’t contact your device.

2. Battery Problem

The battery of your light remote may have gone faulty or you’re using the wrong one. Your light remote device needs a CR2032 3V battery to work.

3. Inappropriate Weather

Using your projector outside, might cause interference and disrupt your remote signal.

4. Remote Not Paired

Your light remote device might have got disconnected from the projector and it will not enable any of the gemmy points.

5. Hardware Issue

Lastly, a hardware problem either with your projector or remote could be the cause of the issue you’re experiencing.

Having that said, proceed with the upcoming solutions to troubleshoot your projector and light remote setup.

How To Fix Points Of Light Projector Remote Not Working?

If you were unable to identify the issue’s cause, don’t worry since we will troubleshoot both your projector and remote.

This will help you quickly resolve the problem and get your light remote working again.

Here are the solutions to fix your projector’s light remote easily.

Solution #1 Discharge Your Light Remote

We suggest discharging your light remote out of any electricity before changing the batteries and proceeding any further.

In case the issue with your remote is power-related, by performing a power cycle, you would have a good shot against the problem.

Here is how to discharge your light remote in easy instructions:

1. Look underneath your remote and locate the battery latch.
2. Pull the latch down and wait for the click.
3. Disengage the compartment and locate the battery.
4. Remove the battery and press each button on your remote for 5 seconds.
5. Re-assemble the remote and test the light points.

Note: Make sure to attach the battery correctly once you’re done with the discharge. 

It must fit perfectly into the compartment and have contact with the power poles of the remote.

If discharging your remote didn’t help, let’s proceed with the next solution.

Solution #2 Replace The Battery

In a situation where discharging didn’t help, try replacing the battery of your remote.

We can easily say that this is one of the most frequently reported causes when there are issues with your light remote.

Here is how to replace your remote battery:

1. Take apart the power compartment of your remote.
2. Eject the battery from its slot.
3. Identify the type of the battery (most projector remotes use CR2032 3V battery).
4. Grab a replacement battery unit and position it into the slot.
5. Re-install the compartment.
6. Test.

Tip: If you struggle with identifying the type of your remote’s battery, simply take the old unit to a local tech store and ask for the same.

Solution #3 Move Closer To The Device

A basic issue that could occur with your projector setup is over-exceeded distance.

Since the light remotes don’t have much of a range, you must make sure that you’re standing close enough to your projector to interact with the device.

Regardless of whether your remote is inside or outside, make sure that you’re standing within 5 meters from your projector.

This is the recommended distance for interaction with any projector device.

Note: Additionally, mind that not pointing the remote towards the projector directly might not enable the gammy points. Make sure to point the remote straight towards your projector.

Solution #4 Troubleshoot The Projector

The problem could be coming from your gamma projector.

In that regard, we’ve separated this solution into 3 parts so you can solve any potential issues with the projector.

Note: Make sure to apply the troubleshooting workarounds in the order we’ve listed them in for best results.

Power Cycle The Device

We suggest power cycling your projector to solve any power-related issues. Simply disconnect the projector from the source for 5 minutes and then reconnect it.

Use Different Outlet

Try plugging your light projector into a different power outlet.

There could be a fault with your projector’s current power source, so plugging it elsewhere might solve any potential issues.

Prevent Overheating/Check Temperature Lights

Your projector has temperature lights. Make sure that they aren’t red and in case they are, prevent overheating your projector.

You can stop overheating by removing any heat conductors close to your projector and preventing any sunlight from flashing on the device for too long.

If the problem wasn’t with your projector, then proceed with the next solution.

Solution #5 Pair The Remote

If nothing worked so far, your light remote may have gotten disconnected from the projector.

In that regard, we suggest reprogramming the remote to the projector to solve the problem.

Here is how to fix points of light remote not working by pairing your light remote to the projector:

1. Make sure that your projector is plugged in and turned on.
2. Point the remote towards the projector.
3. Locate the Home & Enter buttons on the remote.
4. Hold both of these buttons down for 10 seconds while aiming at the projector.
5. Wait for the indicator light.

Note: You must be close enough to the projector while performing the pairing steps. 

Our recommendations would be to stand next to the projector and execute the steps above for best results.

Read Next: Does Ring Alarm Work Without WiFi?

Bottom Line:

Thus, if the gammy points of your remote don’t seem to work, solve the issue by discharging the remote and replacing its batteries.

Next, inspect and solve any ongoing issues with the projector. Lastly, make sure that the remote is correctly programmed and connected.

After understanding why points of light remote not working, you will be able to easily solve the problem with our solutions.

If you end up still not fixing the issue, however, your next step should be to reach out to a technician to review your light remote and projector.