Lasko Heater Blinking 88? – Here’s How to Fix

Is your Lasko Heater blinking 88 and you have no explanation for the problem?

We’ll go over everything you should know about the problem with your Lasko Heater and we’ll also learn the best ways to solve it, all by yourself!

However, you should know that the “88” error could also indicate a critical fault with your heater, that only the merchant could take care of.

To fix when the Lasko Heater is blinking “88”, unplug the device for 5 minutes and disable the “Auto” setting. Drop down the heating temperatures and clean the air filter of the device. Finally, place the heater away from other heat conductors and factory reset it.

Keep reading in order to review the following solutions in more depth and detail!

How to Fix When Lasko Heater Blinking 88?

Here we’ve reached the solutions guide after going through the essentials of the problem!

We’ll be reviewing each of the methods we’ve reviewed above, so make sure to pay great attention to all of the important aspects.

Do not skip any of our solutions and follow the whole guideline in chronological order to achieve the most troubleshooting success.

With that being said, let’s jump in with the guide!

Solution #1 Disable the “Auto” Setting

Especially during winter days, we’re used to keeping our heater working constantly.

\When turning the device on after it has worked for a longer amount of time with the “Auto” setting turned on, will cause the hardware to immediately raise its temperatures.

As a result of that, you’ll get the blinking “88” message on the device’s screen as an indication that the hardware is maintaining unnatural temperatures due to the enabled feature.

• Based on your Lasko Heater, use the physical control/button to turn off the auto

We could all agree that the auto feature is way too comfortable and valuable to be turned off.

But you should test if that will resolve the error that occurred with your heater.

Note: Keep the auto feature along with any other settings disabled for the rest of the guide.

Solution #2 Blow Off the Heater’s Filter

The Filter of the heater is where the dust gathered up inside of the device is being filtered.

Essentially, your heater withdraws air from the surrounding environment in order to keep its hardware cool down.

When that withdrawal of air happens, particles of dust are also being sucked in which could pile up within the hardware, unless they are collected by the filter.

Here’s how to blow off the Lasko Heater’s filter in easy steps:

1. Use a screwdriver to undo the side panel screws.
2. Take off the Side Panel of your Lasko Heater.
3. Expose the Internal Air Filter.
4. Furthermore, unscrew the FIlter’s screws.
5. Take off the air filter.
6. Use a vacuum cleaner to suck out all of the dust on the filter.
7. Reinstall the filter inside of your heater.
8. Test…

You could also wash the filter using cold water, but it must completely dry up before reinstalling it.

Alert: Placing the filter inside your heater while still wet could severely damage the hardware.

Solution #3 Lower the Temperature Setting

The “88” error code mainly occurs due to High-Temperature Settings on your heater.

The hardware of the heater works in the following way – the stronger heat it emits, the hotter its hardware will become.

Since the “88” error is an indication of a hardware overheating of the heater regarding the surroundings, you should optimally lower the heating setting and test.

• Based on your Lasko Heater, use the on-screen controls to drop the temperature

You don’t have to drop the temperature of the heating dramatically, but something enough to help your heater partially cool down.

It’s essential for the device to maintain regular hardware temperatures since overheating could cause the device to immediately shut down and stop working in the upcoming moments.

Note: Keep your heater at low heating temperatures until the problem is identified.

Solution #4 Power Cycle the Device

A quick and efficient solution to your Lasko heater’s both hardware and software problems is the Power Cycle.

This is the ultimate hardware reset of the device that covers any problems that occurred with the device.

The power cycle process consists of cutting the device’s power supply, in order to achieve full discharge of the hardware’s electricity.

Let’s learn how to execute a power cycle:

1. Turn off the heater by pressing the Power Button.
2. Wait for the device to shut down.
3. Unplug the Power Adapter of the Lasko Heater.
4. Wait for 5 Minutes while the heater is discharging.
5. Re-attach the power adapter of the device to the power outlet.
6. Test…

In case that doesn’t help, keep reading!

Solution #5 Place Away from Heat Conductors

If your heater is not the only active heating in the room, you should pay attention to the positioning of the device.

The blinking “88” on your heater could occur, especially whenever the device’s internal outlet and inlet fat are failing to reduce the temperature and cool up.

In that regard, place your heater away from your Heat Conductors near the device!

If let’s say you have a fireplace burning in the room, but you’ve turned on the heater until the fireplace manages to increase the room temperatures enough.

You should keep in mind that the fireplace is emitting strong heat to the near surroundings and if your heater is in that range, it could also overheat.

• Place the heater as far away as possible from the primary heater of the room you’re in

Once replaced the device, turn it on and check if the “88” error would still occurs.

Note: You should not use your heater too much if the room is already warm enough.

Solution #6 Reset the Lasko Heater

Finally, we’ll be doing a Reset on your Lasko Heater.

The chance that a problem has impacted the software of the device is too great to avoid performing a reset.

Since this is exactly what the Factory Reset specializes in (software problems), the next thing you should do to your heater in regard to troubleshooting is exactly that.

Let’s learn how to perform a Factory Reset on your Lasko Heater:

1. Ensure your heater is plugged in.
2. Press the Power Button on the device.
3. Without pressing the button, proceed to hold it for 30 seconds.
4. Keep the heater unplugged for an additional 15 Minutes in order to achieve a reset.
5. Reconnect the heater’s power adapter back into the source.
6. Turn on the device by pressing the power button.
7. Test…

The least you’ll have to keep your heater unplugged to achieve a reset is 10 minutes, but 5 additional minutes won’t harm, right?

Once that cooldown has elapsed, feel free to reconnect your heater, press the power button and then test the device!

Alert: If the problem is still occurring, contact Lasko for more assistance!

Lasko Ceramic Heater Blinking 88 – Quick Fix

If you’re experiencing the “88” error on your Lasko Ceramic Heater, then it most certainly means that something in the device’s hardware has gone wrong.

Ceramic Heaters with quite older hardware than digital and space heaters are more likely to develop similar problems.

That’s why we’ll review three additional solutions that you could benefit from in troubleshooting your heater!

Try all of the above solutions on your Lasko Ceramic Heater before proceeding!

To fix when your Ceramic Lasko Heater is blinking “88”, try the following:

• Unplug the heater – Disconnect your heater’s power cable for 5 minutes
• Disable Features – Disable any functionality features using the rotation switches
• Smooth surface level – Place your heater on a smooth surface with no obstructions

If you’ve done all of the following instructions and your Ceramic Heater still displays this type of error, it is probably an internal hardware fault with the device.

Consult with Lasko soon.

Quick Recap:

Hence, to fix when Lasko Heater blinking 88, disable the “Auto” setting on the device if it is enabled. Next, lower the temperature setting and blow off the air filter clean. Coming up, reposition the heater and undergo a Factory Reset on the device.

If you’re still experiencing problems with your Lasko Heater, regardless of whether it is a ceramic, digital or space, contact Lasko.