Looking for a solution to the Dynex TV remote not working? You’ve just found it!
In this guide, we will go over all of the cases impacting your Dynex TV remote and then review the best-working solutions to solve the problem.
We will also provide you with a variety of users’ opinions and how the Dynex TV users fixed their remotes!
To fix a Dynex TV remote, first, make sure that the device has a clean line of IR sight to the TV. Next, power discharge the remote and replace the batteries. Then, attempt reprogramming the Dynex remote to your TV and lastly, perform a reset on it.
Let’s review the possible causes for this problem, reported by Dynex users as the most frequent occurrences, and then proceed with the fix methods.
Why Does The Dynex TV Remote Control Not Working?
If your Dynex TV remote refuses to work with your Dynex television, chances are that the issue lies within your remote’s hardware.
Although the most often problems with remotes are with their batteries or with the line of sight, the issue could also be software-related.
Here are some well-known issues that could impact your Dynex remote:
1. Worn-Out Batteries
One of the most often occurrences is worn-out batteries inside of your remote control.
2. Remote Not Programmed
Your Dynex TV remote could have disconnected from the TV and therefore you will have to reprogram the device.
3. No Line of Sight
The technology within your Dynex remote requires a clean path for the signal that reaches your TV, in order for the remote to work.
4. Hardware Damage
If you’ve damaged your Dynex remote lethally, you may find it impossible to use the device anymore.
5. TV Problem
An issue with the TV might be blocking the signal of your Dynex remote, therefore deceiving you into thinking that the remote is faulty.
After taking a quick look at the following causes, keep reading to learn how to solve the issue of your Dynex TV remote in easy solutions.
How To Fix Dynex TV Remote Not Working?
If your remote doesn’t work, the first thing you should do is restart your TV.
There’s a high chance that a temporal bug or glitch is preventing the remote signal from reaching the receiver (your TV).
In that regard, a restart should be the first thing you should attempt.
If a reboot didn’t help, proceed with the following solutions to fix your remote:
Solution #1 Power Cycle TV/Remote
The first and the best-working solution is to power cycle both your TV and remote.
This process includes discharging the device out of any electricity, giving it a proper power cycle, and eliminating any issues both with the hardware and software.
Let’s begin with power cycling your remote:
How To Power Cycle Dynex Remote?
- Turn your remote upside down.
- Eject the batteries from the compartment.
- Press the power button for 10 seconds on the remote and the rest of the buttons but for 5 seconds.
- Re-install the batteries and compartment.
How To Power Cycle TV?
- Turn off your TV through the power button.
- Disconnect the power adapter.
- Standby for 5 minutes.
- Re-attach the adapter and test.
Note: When power cycling your remote, don’t hold any button for longer than 10 seconds to avoid resetting your remote, which we will do later in the guide.
Solution #2 Solve Interference
Chances are that there is an interference somewhere across your setup.
That’s why the next thing you should do is clean your TV/remote connection out of any available interference, interrupting the signal actively.
Here are some factors of interference you can consider solving:
1. Solid Objects
Ensure no solid obstructions or objects are positioned on the path between your TV and remote.
2. RF Transmitters/Receivers
TV boxes, set-top boxes, radios, and other RF transmitters might be accepting the signal of your remote, instead of the Dynex TV.
3. Other Televisions
Other TVs positioned close to your Dynex TV might be accepting the signal too.
4. Dirty Remote “Eye”
Clean your remote’s eye and remove the dirt that is interfering with the signal.
Note: Check if your remote’s issue has been solved after each of the following solutions, before moving on to the next one.
Solution #3 Replace Remote’s Batteries
If there was no interference, you should replace your remote’s batteries.
Your remote could be running out of charge and causing it to be unable to interact with the Dynex television.
We assume that you’re familiar with how to replace your remote’s batteries so make sure to insert a fresh pair before continuing any further.
The only thing you should be aware of is how you insert the batteries.
Note: Ensure that the “-” on the batteries is matched with the “+” on the remote and the other way around.
Solution #4 Reprogram Dynex Remote To TV
There’s a chance that your Dynex remote got disconnected from your TV or Dynex TV.
Fortunately, there’s an easy way to get the remote reprogrammed back to the TV unit so you’re able to control the TV again.
Here’s how to reprogram your remote to the TV in easy steps:
- Ensure that your TV is up and running.
- On your remote, hit the TV and SEL buttons for 3 seconds.
- Enter the 0463 code for your Dynex TV.
- Verify with the VOLUME + button.
Note: If by any chance you’re not using a Dynex TV, here are some of the codes for the famous TV brands:
- Philips – 2195, Panasonic – 2153,
- LG – 1628, Element – 3477,
- Toshiba – 3021, Samsung – 2448,
- Vizio – 3211, Insignia – 1368,
- Proscan – 2279, Sharp – 2550,
- and Sony – 2679;
Solution #5 Reset The Remote
If nothing from our solutions worked so far, you should perform a factory reset on your Dynex TV remote.
For that purpose, you will need to have the batteries inserted within your remote because you will have to take them out.
Here’s how to reset your Dynex remote:
- On your remote, remove the batteries.
- Press the power button for 20 seconds.
- Reinsert the batteries.
- Your remote is reset!
Note: There won’t be any identification that your remote is actually reset.
This was how to fix your Dynex remote. If you wish to receive any additional resistance over-the-top, contact Dynex to learn how you can additionally troubleshoot your remote.
Read Next: How To Fix NBC Sports App Authentication Error?
Final Word:
Thus, to fix a not working Dynex TV remote, power cycle both of your TV and remote, followed up by replacing the batteries. Resolve any interference in your setup and reprogram the remote. Finally, perform a factory reset on your Dynex TV remote.
After learning why the Dynex TV remote not working and you’re familiar with how to solve the problem, the rest is up to you.
Perhaps, your remote is due for a replacement if the issue hasn’t been solved by now, but still, make sure to reach out to Dynex for more help!
- Kwikset Smart Lock Code Change – FoolProof Guide - May 25, 2023
- How to Connect Turntable To Marshall Speaker? - May 25, 2023
- Asko Dishwasher Not Drying? – Complete Fix Guide - May 25, 2023