If you’re wondering how to stop LED lights from changing colors, then this fix guide is for you. Let’s begin with unveiling why this is happening.
The reasons why your LEDs are changing color by themselves are the following:
- Software issue
- Broken remote control
- Fluctuating voltage
- Faulty dimmer switch
- Incompatible extension
To stop the LED lights from changing colors by themselves you would need to inspect the power source, restart the dimmer switch and remove any unsupported extensions. Then you need to check the buttons on your remote and prevent any overheating.
How To Stop LED Lights From Changing Colors – Methods
There are various reasons why your LED lights could be changing their color on their own.
Our methods are designed to tackle each possibility until you find the true reason why this is happening and eventually solve it.
Let’s start with the obvious:
The first thing that you should attempt is to prevent using your LED lights for long intervals of time.
When using a certain device for too long, without the unit having its downtime, strange occurrences may happen.
If you’ve been using your LED lights 24/7 non-stop, the LEDs may start flickering weirdly or even change colors as the problem you’re experiencing.
In that regard, if you’ve had your LED lights running for longer than several days, make sure to turn them off for an hour.
Tip: Ensure that you have also unplugged the dimmer switch from the power supply.
Overheating is what causes problems with the LEDs the most.
Whenever a LED light overheats, it can either completely shut down or can also start having power fluctuations which are essentially changing the light color on your LEDs.
To determine the temperature of your LED lights, it’s enough to just touch their bulbs.
Usually, LED lights have to be cool upon touching. If yours are hot (moderate), then there certainly is overheating going on.
Here are all of the causes of overheating of your LED lights:
- LEDs are covered with a blanket.
- Not enough space for air circulation and ventilation.
- LEDs are too close to a heat conductor.
- The LED lights are being exposed to sunlight from outside.
- It’s too hot in the room that the LEDs are in.
These are the main causes for overheating with your LEDs. Make sure that you avoid each one of these to preserve the LED’s cool temperatures and avoid any overheating in the future.
Tip: After applying each of the steps above, test your lights for 5-10 minutes to determine if the temperatures would now drop.
LED light strip extensions are what’s making the color of the lights change. When having several LED light strips and you want them to work together, you use extensions.
Unfortunately, if the strips and the extension are from different brands, this means no good.
The power of your lights may fail to circulate correctly and the colors will start changing by themselves.
In this method, you should disconnect any LED light extensions you’ve connected to your strips and test the LED lights without them.
Note: If the extensions you use with the strips share the same brand, try changing their places instead.
If you can’t figure out how to stop LED lights from changing lights, then you should start looking for the problem at the power source.
As we’ve mentioned earlier, the power supply is mainly what causes the lights of your LED strips to change color.
By plugging the switch into an alternative power source, you should get the problem fixed.
- To change the LED lights’ power source, go over to the dimmer switch controller, unplug and press the power button to shut the lights off. Next, unplug it from the power source and connect the unit to a different power outlet.
Note: Avoid using any power strips or dividers to connect the dimmer switch to, since this could cause additional power problems.
The main culprit for the problem you’re experiencing could be the remote.
If the LED lights keep changing the color by themselves, chances are that there is a stuck or faulty button on the remote or the signal is incorrect.
It’s no use changing the remote’s battery since in most cases where the lights change by themselves, the remote’s end-life has been reached.
If the controller remote of your LED lights has gone faulty, there really isn’t anything you can do to fix it, except for replacing the unit.
Note: LED light controller remotes can be acquired from every technical store near your location and don’t cost much, to begin with.
There’s a way to reset your LED lights through the dimmer switch, to figure out if this is going to solve the problem.
For this method, you will only need access to your LED’s dimmer switch and its power button.
Here’s how to reset the LED lights in easy steps:
- Go over to the dimmer switch.
- Press and hold the power button.
- Hold it down for 10 seconds.
- Release the button and wait for one minute.
- The lights are reset!
Notice: Do not let go of the button before the 10 seconds or the factory reset of the lights will fail.
The color change could be formed due to a failed connection to the dimmer switch.
In that case, you should first attempt to reconnect the strip to the dimmer switch. If that does not help, then maybe the dimmer switch is faulty.
It’s recommended to get a dimmer switch, compatible with the brand of your LED strips.
If all of your LED light components are compatible, you shouldn’t have any problems, similar to the color changing of the lights you’re currently experiencing.
In that regard, research the brand of your LED strips and look for a dimmer switch that is either of the same brands or is compatible.
Either way, you will get the most out of your LED lights and prevent any further complications and glitches from occurring.
- Disconnect the LED strip from the current dimmer switch, by pressing the latch down.
- Grab the new dimmer switch and connect it to power.
- Hold the connection latch downwards as you connect the LED strip.
- Check if the issue still occurs with the new dimmer switch.
Recommendation: If you’re hesitant about what dimmer switch you should get, better consult with the manufacturer of your LEDs.
The solution to LED lights changing colors on their own includes a power circulation followed by removing the extensions and replacing the remote. Then you need to change the power source and reconnect the dimmer switch. Lastly, you should perform a rest on the LEDs and if it does not work, replace the dimmer switch.
Read Next: Can LED Strip Lights Cause A Fire?
Now that you’re aware of how to stop LED lights from changing lights color, you should be able to resolve the problem permanently.
Don’t hesitate to check the brand of your strips online and what other users have to say about their units.
- Shark Robot Vacuum Obstruction Error? (7 Proven Solutions) - December 7, 2023
- My Dyson Hair Dryer Stopped Working? (7 Quick Solutions!) - December 7, 2023
- White Rodgers Thermostat Blinking Flame? (7 Proven Fixes!) - December 5, 2023