How To Clean GE Profile Dishwasher?

How To Clean GE Profile Dishwasher? When you have used your dishwasher for a while, it is time to clean it up and prevent bad smells. 

You must disassemble all possible parts of the GE Profile Dishwasher and clean up everything correctly. Some products are advised, as you will see in the guide below.

Is this your first time cleaning the GE Profile Dishwasher? Then, you have nothing to worry about, as we will guide you through all steps.

How To Clean GE Profile Dishwasher – Step by Step

No one wants a dishwasher that smells bad. But, after a while, if you don’t clean your GE profile dishwasher, it might start smelling from the scraps left within it.

That means it is time to clean!

So, how do you clean? First, you must proceed carefully to avoid damaging any essential components, especially electrical ones.

Also, you need to make sure you clean everything. 

We will teach you which steps to follow, useful tricks, and what products are better for GE Profile Dishwasher cleaning.

Step #1: Prepare The Cleaning Items

Before you start a cleaning session in your dishwasher, you must ensure you have all the necessary items for the task.

Luckily, you can clean your dishwasher without demanding items. Most of them you can find in your house already.

Let’s check them:

• Warm water
• Baking soda
• Soft cloth
• Alcohol
• Small toothbrush
• Sponge
• White vinegar
• Detergent
• Rust remover (depending on the state of your dishwasher)
• Lemon juice (optional)

Alert: Never use bleach to clean your dishwasher!

Step #2: Preparing The Dishwasher For Cleaning

When the last wash cycle is complete, you should empty the dishwasher and remove the rack that is located at the bottom. 

A screen with holes may be seen on the bottom of the dishwasher, just below where the spray arms meet the dishwasher’s base. 

Tip: Remove any water that may be trapped at the bottom of the appliance using a cup. If there is a blockage in the filter, you will notice food particles floating on the surface.

Step #3: Clean The Door

You can clean the outside with a sponge and some soapy water. 

The alternative is to use a homemade product specifically designed for the dishwasher. Create a cleaning solution by combining 1/4 cup baking soda and 1-quart water.

After washing, dry the door with a clean, soft towel/cloth. To remove stubborn fingerprints and smudges, use a little rubbing alcohol on a soft, dry cloth.

Now open the door to clean its inside. Scrub the door frame with a tiny toothbrush dipped in hot, soapy water.

It is imperative that you thoroughly examine the hinges, as well as the grooves of the rubber seal/gasket. 

If there is a lot of accumulation, you may need to use an abrasive cleaner and scrape gently. 

Tip: Use a sponge dampened in hot, soapy water to clean off the ensuing filth. Further, use a fresh, damp sponge to wipe off any residual cleaner.

Step #4: Locate The Perforated Screen/Filter

The General Electric Dishwasher Profile’s perforated screen may be found at the very bottom of the appliance, just below where the spray arms terminate. 

Because it serves such a critical protective function during a wash, you must clean it consistently to ensure it can carry out its responsibility effectively. 

Cleaning the perforated screen, sometimes referred to as the sump filter, is a simple process that only requires goods often found in households. 

Tip: It is recommended that you manage to do this activity every four to six months.

Step #5: Cleaning the Screen

Use a dish towel to remove any food particles that have settled on the screen’s surface.

And use another towel to remove any additional residue accumulated on the device’s base. 

Only water will be able to flow through when the filter is clean.

To remove the filter from the washing machine, lift the cup assembly on top of it.

Next, clean and remove any hardened buildups on the filters by rinsing the top and bottom under running water and then using a soft nylon brush to do the job. 

To assist in the removal of stubborn stains, try using warm water with dishwashing detergent added to it in a small amount.

Step #6: Get Rid Of Rust Stains (situational)

Rust stains on your dishwasher’s interior might result from your water supply or the condition of your pipes.

To fix that, do the following:

1. Open the soap dispenser of the dishwasher
2. Put some rust remover in it
3. Sprinkle more rust remover on the bottom of the device
4. Run a complete wash cycle.

If you don’t address the underlying cause of the rust stains, you will likely need to do this maintenance frequently. 

Tip: You must call a plumber and install a filter to aid in rust prevention.

Step #7: Eliminate Hard Water And Mineral Buildup (situational)

Hard water deposits or mineral buildup can occur in your dishwasher. Lemon juice can do wonders to get rid of this issue.

Run a standard cycle with a cup of lemon juice on your dishwasher’s top rack or basket.

Hard water stains and iron buildup ought to be eliminated with the help of lemon juice.

Note: If this is a recurrent problem, you should clean it with lemon juice monthly.

Step #8: Getting Rid of Clogs in the Dishwasher

Finding and removing obstructions that source unpleasant odors is another step in the GE dishwasher cleaning process.

The following is a step-by-step for removing foul-smelling clogs in the areas where they are most prone to occur:

Start the Trash Disposal 

If you have a garbage disposal, turn it on and let it run for at least 10 to 20 seconds before starting the wash cycle. 

That will eliminate any unpleasant-smelling food leftovers accumulated in the drain that the disposal and the dishwasher share.

Clean Out the Air Gap 

If you have an air gap near the kitchen faucet, it may gather odorous food remains that clog the dishwasher.

You can avoid that by clearing out the air gap:

1. Remove the cap 
2. Clean it out before starting a wash cycle. 
3. Remove any debris you find.

Clear Clogs in the Drain

To clear blockages in a dishwasher drain, combine two tablespoons of vinegar with one tablespoon of baking soda and then pour the solution down the drain. 

Please let the mixture settle for 10–15 minutes.

Then, before beginning a regular wash cycle, remove the solution and blockage by flushing the system with hot water.

The hottest, the better.

Step #6: Put in order

After all the steps above, it is time to put everything back in order. The first step is reinstalling the filter you removed for cleaning.

Then move the bottom shelf into its proper spot. Check that the filter is in the appropriate place, then start a regular cycle with racks and walls empty. 

That will ensure that all the parts are thoroughly cleaned.

Tip: Put a reminder in your calendar to do this procedure once a month.

Read Next: Frigidaire Affinity Washer Not Doing Final Spin?

What We Learned

How To Clean GE Profile Dishwasher? If you have some cleaning products in your house, getting to the task is no problem.

Most of the items you will need to clean your GE Profile dishwasher are of easy access.

When cleaning, you must pay attention to all parts, remove debris and clog you find, and check for rust stains and mineral buildups.

If you pay attention to our full guide, you will do just fine.