Dynex DX-RC01A-12 Not Working? – Complete Fix Guide!

Wondering why is the Dynex DX-RC01A-12 not working out all of a sudden. Keep reading!

There are quite a few reasons why a Dynex remote would become unresponsive and in this guide, we’re going to unwrap this topic and provide a solution for any cause.

The Dynex DX-RC01A-12 remote might stop working when the batteries are dead or when the IR signal is unable to reach the TV. In addition, users should attempt to re-pair the remote to the TV in case it’s disconnected and perform a power cycle to conclude!

Let’s learn more!

Why Is Dynex DX RC01A 12 Not Working?

Your Dynex model DX-RC01A-12 TV remote may have stopped working due to multiple reasons.

Generally, there is one shared cause among all occasions where a remote would stop working and this is the batteries.

Excluding the batteries, here are some of the most frequent causes:

• The “eye” of the remote or the TV receiver is obstructed.
• There is wireless signal interference impacting the signal.
• The remote is “unprogrammed” from the TV.
• A hardware problem has occurred in the remote.

Before we proceed, note that if your remote happened to be an object of lethal water or drop damage, the issue may be irreversible.

If you notice any serious damage done to the hardware of the remote, it’s best to purchase a replacement unit.

Let’s next jump into the best-working solutions against not working Dynex TV remote:

DX-RC01A-12 Not Working – Fix Solutions!

Now that we got the causes out of the way, let’s begin troubleshooting your DX-RC01A-12 remote.

Ensure to follow our solutions consecutively and test your remote after each step to identify if the issue has been resolved.

Follow these instructions to get your Dynex remote working again:

Solution #1 Soft Reset the Remote

Some people may call it a power cycle, hard reset, or soft reset but the process has a shared goal – to discharge your remote and restart ALL services.

This is the easiest and fastest solution to apply so that’s why we begin our guide with the power circulation!

Here’s how you can soft reset your Dynex TV remote:

1. Put the remote upside down with the buttons facing down.
2. Remove the battery compartment cover from the remote.
3. Once the batteries are exposed, use your fingers to take them out.
4. Press and hold each button on the remote for 5 seconds.
5. Hold the power button for 30 seconds.
6. Reinsert the batteries into the remote and close the compartment.
7. Check if the remote is going to work now.

Note: When reinserting the batteries, make sure that the polarity installation is intact.

Solution #2 Reprogram the Remote

Although the Dynex DX-RC01A-12 remote is usually reprogrammed, the device could have disconnected from your TV as a result of a software reset.

Especially if you’re not using a Dynex TV along with your Dynex remote, disconnecting might be the problem.

Each TV brand has its own programming code for the Dynex remote!

Here are some of the TV codes for more popular brands:

• Samsung – 0105, 0077, 0076
• KENWOOD – 0004, 0009
• Toshiba – 0159, 0178, 0120
• Hitachi – 1004
• PANASONIC – 0171, 0148, 0054
• RCA – 0031, 0004, 0100
• Philips – 8888
• Dynex – 0463

If you happen to be unable to locate the remote programming page, use Google and follow the instructions to get the Dynex remote re-programmed to the TV.

Alert: Codes are always entered without spaces or special characters!

Solution #3 Replace the Remote Batteries

If the remote wasn’t unprogrammed either and is still unresponsive, you should now replace the batteries.

The remote could have run out of charge, which will result in it no longer being able to control your TV, therefore sending signals.

Here’s how to replace your Dynex DX-RC01A-12 remote batteries in easy steps:

1. Purchase 2 new AAA batteries for replacement.
2. Put your remote on a flat surface and take off the battery cover.
3. Eject the old batteries out of your remote.
4. Put the new AAA batteries inside your remote.
5. Close the battery compartment cover.
6. Check if your remote would work now.

Alert: Using second-hand batteries will not guarantee proper remote functioning!

Solution #4 Resolve Wireless Interference

Wireless signal interference could be disrupting your Dynex remote signals and prevent the IR signal from reaching the TV.

It may not sound like a big deal, but certain objects and items around or near your TV/remote could cause interference with the remote signal.

Objects of wireless signal interference could be the following:

1. Radios/baby phones with wireless signals.
2. RF transmitters.
3. Solid objects/furniture in between your remote and TV.
4. Devices with a turned-on Bluetooth near your TV or remote.

Once you’ve made sure that none of these items are in your TV or remote’s surroundings, level the TV so it is in line of sight with the remote’s “eye”.

Test whether the problem is now solved.

Note: Keep in mind that other remotes that are programmed to your TV could also cause interference with the signal.

Solution #5 Hard Reset the TV

By now, chances are that there is a problem with your TV, rather than your Dynex remote.

Performing a hard reset as you did on your remote, will discharge the TV and refresh its software which could resolve this problem for you.

Here’s how to perform a hard reset on your TV:

1. Turn off the TV using the physical power button.
2. Disconnect the power adapter of the TV from the source.
3. Wait for at least 5 minutes until the TV completely discharges.
4. Re-attach the power adapter of the TV back into the power port.
5. Turn on the TV.
6. Check if your Dynex remote would work now.

If you’re hesitant that there might be a problem with your TV, you should test with an alternative remote.

If you have the TV’s original remote or a universal one, don’t hesitate to program it and check if the problem is with the remote or the TV.

Note: If you keep the TV unplugged for less than 5 minutes, the hard reset won’t discharge the device completely.

Solution #6 Clean the Remote

The last thing you should do is make sure that your remote’s hardware is not obstructed by any hair, dust, or debris.

Sometimes, a remote that is used for a long time may get its battery compartment clogged, therefore, the change won’t reach the device.

Follow these instructions to clean your Dynex remote appropriately:

1. Turn the remote upside down.
2. Open the battery compartment and eject the batteries.
3. Remove dust, hair, and debris from the electricity poles.
4. Clear the entirety of the battery compartment.
5. Clean the IR “eye” on the front of the remote.
6. Re-insert the batteries and test.

In case the remote is now working, then probably the battery contact was obstructed or the IR eye was clogged.

Ensure to maintain the remote regularly to keep the functionality intact and prevent such problems from appearing in the future.

Dynex Remote Still Not Working…

In case you’ve attempted all of the solutions in this guide and the remote still does not make any indication that it’s working, maybe the unit is dead and you would need a replacement.

Before purchasing anything, the one last thing that you should attempt is to reach Dynex customer service to ask for help.

You can contact the Dynex support team in two ways:

• Call at 703-631-7800
• Send an email to techservice@dynextechnologies.com

The most important question that you should ask:

“Is my remote compatible with the TV brand I am attempting to pair?”

With a little luck, the problem might turn out to be related to compatibility, therefore your remote is still functional.

In contrast, the worst-case scenario would require servicing.

Read Next: How To Stop TV Remote From Controlling Two TVs?

Quick Recap:

Hence, the Dynex DX-RC01A-12 is not working because the battery charge is low or because the remote has gotten disconnected from the TV. Users should re-pair the remote, then perform a power cycle and clean the IR “eye” both on the remote and TV.

Final Thoughts:

Now that we know why Dynex DX-RC01A-12 not working and how to solve the problem with a few easy solutions, we will now be able to control our TV.

What we’ve learned is that the compatibility between the remote and TV brand must be checked before any troubleshooting!

We hope that this post was helpful and for more relevant guides check our blog!