Amana Dryer Not Getting Hot? – Here’s How to Fix

Wondering why is Amana dryer not getting hot? No worries, we’ll help you to fix this!

It is very frustrating for homeowners, especially when the dryer won’t get hot.

There are different variations of the problem involving the heater stopping midway, not having enough heat, or not getting hot at all.

All possibilities share the same cause and the issue can be solved in minutes!

There are different factors that’ll prevent the dryer from getting hot. It can be any fault in dryer electrical components, heat source components, or shortage of gas or voltage. The solution requires an inspection of all factors involved so it’s easy to find the culprit.

Now, let’s find out more detail about the causes of the dryer not getting hot!

Why Is My Amana Dryer Not Getting Hot?

If your dryer isn’t heating up, there might be a serious issue with the appliance, or it could simply be something simple that has to be fixed.

It’s important for you to understand all the causes of this issue before troubleshooting your dryer, so you can approach the situation accordingly.

The following are the most frequent causes of a not getting hot dryer:

• Low Gas or Power Supply 
• Faulty Heating Element of Dryer
• Blown Thermal Fuse
• Faulty Limit Thermostat
• Dirty Lint Screen or Clogged Vent
• Faulty Gas Valve Solenoid
• Defective Gas Igniter or Flame Sensor
• Defective Cycling Thermostat

Although the aforementioned causes are the most typical ones, still the dryer’s heating function can also be impacted by many other factors as well.

We’ve made sure to include everything in the solution guide below so jump in and solve the issue in minutes!

How To Fix When Amana Dryer Not Getting Hot?

You now have enough understanding of the possible causes of your Amana dryer heating problem to identify the issue’s source.

However, you must be sure to carefully follow each method’s steps if you want to fix your dryer without damaging the rest of your appliance.

Let’s jump right in!

Solution #1 Check The Power Or Gas Supply

Checking the Gas Supply or the Electrical Voltage that your appliance is getting should be your very first step.

Amana offers both gas and electric dryers, which will help in their proper functioning and both types of dryers need a certain amount of voltage or gas to operate.

Check The Electrical Dryer Power Voltage: 

1. Use a Multimeter and test the voltage from a power outlet.
2. The AC line has to show 240V for proper operation.
3. Then, access the back of the dryer to test the voltage from the appliance as well.
4. Unscrew the dryer back terminal and a metal plate to get access to the dryer legs.
5. First, check the right leg via a multimeter and then the left one.
6. Also, make sure to note down the voltage of both legs.

Once you have done this, then check whether your dryer outlet and the dryer legs have the same 240V power.

If yes, then the problem is not in the outlet so keep reading!

Check The Gas Dryer Supply

1. First, locate the dryer Gas Valve from behind the dryer.
2. Make sure the valve is open and not stuck.
3. Next, carefully check if there is any fault in the gas valve.
4. Also, ensure that the gas is coming and the pressure is also good.

Note: If you notice low pressure, then you need to simply wait until the pressure comes high!

Solution #2 Clean the Lint Screen

Cleaning the dryer lint screen is essential for the dryer’s effective performance.

The lint often becomes trapped by soap residue or other airborne particles and blocks airflow into the dryer. This not only affects the dryer heater but also increases the risk of fire.

Therefore, try cleaning the lint screen on your dryer and make sure to follow the steps below for better orientation.

Here is how to clean the dryer lint screen:

1. First, locate the Lint Screen from the top of your dryer or the door opening area.
2. Next, remove the trap from the dryer to clean the lint by using your finger.
3. If you notice any stuck lint on the screen, use warm water and detergent.
4. Then, simply use a vacuum cleaner to dry the lint screen.

Note: Make sure to clean the lint screen after every load in the dryer!

Solution #3 Clean the Dryer Vent

The Amana dryer vent will help the device exchange airflow inside and outside of the appliance.

However, the vents usually become blocked over time, thus cleaning is clearly important.

If the dryer isn’t heating up, it might be because your dryer vent is too dirty and clogged, or bent.

Note: Amana recommends that users use only rigid metal vents for dryer efficiency!

Here is how to clean the dryer vent effectively:

1. First, locate the vent from inside your Amana dryer.
2. Then, use a vacuum to remove all lint and debris from both sides of the duct.
3. Next, remove the exhaust hood vent from the dryer.
4. Use a vacuum to clean the vent as well as the place where the vent attaches.

With the dryer vent unclogged, check whether the Amana dryer is now getting hot!

Tip: It’s recommended to carry out a proper service of your Amana dryer every year! 

Solution #4 Test The Thermal Fuse

The dryer’s Thermal Fuse will prevent it from overheating, but it will blow whenever the temperature rises over a certain safety threshold.

Your dryer has a blown thermal fuse, and that’s why it is unable to get hot so a replacement of the fuse is the only way to fix this issue!

Alert: Make sure to unplug your dryer before repairing it!

Here is how to replace the dryer thermal fuse:

1. Unscrew the Back Rear Access Panel of your dryer and remove it.
2. Next, locate the Thermal Fuse and disconnect the wire harness from it.
3. First, test the fuse via a Multimeter for continuity.
4. If there is no continuity, then simply replace the thermal fuse in your dryer.
5. Lastly, connect the wires harness back to the fuse screw of the rear access panel.

After replacing the thermal fuse in the dryer, plug the dryer into an outlet and test the heating!

Solution #5 Inspect Limit Thermostat

The limit thermostat is also responsible for the control of heat in the dryer but when it gets faulty it erroneously assumes that the dryer is overheating even though it is not.

Next, it sends a signal to the main board to stop heating the dryer and the culprit is typically in the Limit Switch!

Here is how to inspect the limit thermostat on the Amana dryer:

1. First, make sure the Amana dryer is unplugged from the power.
2. Next, unscrew the dryer Rear Access Panel from the back.
3. Locate the High Limit thermostat in the assembly.
4. Disconnect the wire harness from it to take it out of the dryer.
5. Test the switch via Multimeter for continuity. 
6. In case there is no continuity, then replace the switch.
7. Lastly, connect the wire harness and rear panel back.

With the new limit switch, the Amana dryer should be getting hot pretty quickly and be able to work for hours without interruption.

Make sure to test the Aman dryer before continuing.

Solution #6 Check the Gas Valve Solenoid

Amana dryers have gas valve solenoids that’ll help the igniter to glow to provide heating from the valve to the overall dryer.

If your dryer is still not heating up, it’s possible that either the solenoid coils or another component of your device have failed, thus the igniter is not working.

Note: You have to replace both solenoid coils even if only one has gone bad!

Here is how to check the dryer gas valve solenoid:

1. Unscrew the Front Panel of your Amana dryer and place it aside.
2. Then, locate the two solenoid coils from the front bottom of the dryer.
3. First, unplug the gas valves from the coils and then unscrew its bracket.
4. Set up the new solenoid coils there and connect the valve back to the coil.
5. Screw the front panel of the dryer and then test your dryer.

Tip: If your dryer still is not getting hot then we recommend testing your dryer gas igniter and flame sensor as well!

Solution #7 Check The Dryer Heating Element

The heating element in the dryer helps the upcoming air to heat before it goes to the drum.

Like other components, over time the heating element also gets faulty and doesn’t heat the air and that’s why your dryer is still not getting hot.

So, replacement is the only way to fix this mess!

Here is how to check the dryer heating element:

1. Make sure to unplug your dryer from the Power Outlet.
2. Next, unscrew the back panel of your dryer.
3. Disconnect the wires from the right panel and note down the wire’s orientation.
4. Remove the heating element from the dryer and test it via a Multimeter.

If there is no continuity on the meter for the heating element, then replace it and securely reassemble all the components.

This should help your Amana dryer get hot again.

Read Next: Frigidaire Affinity Dryer Not Heating?

Quick Recap:

Thus, whenever your Amana dryer not getting hot, you first need to ensure that your machine is getting sufficient power or gas pressure.

In addition, we need to clean the lint screen and unclog the vent to clear the airflow before testing the Thermal Fuse, High Limit Switch, and Heating Element.

We hope that this guide was helpful and for more relevant content, check our blog!