Wyze Camera Night Vision Not Working? (Fix it FAST!)

Wyze camera night vision not working can be difficult to troubleshoot, as you can’t know for certain what is causing your camera to malfunction.

If you face this exact issue, don’t worry; our guide has some fixes prepared for you to try.

To fix your Wyze camera night vision not working, start by checking if it’s properly configured and enabled. Next, adjust your infrared sensitivity and light setup.

Now that you know a few of the fixes we have prepared for you in this troubleshooting guide, let’s first see what causes Wyze night vision issues in the first place.

Why Is My Wyze Camera Night Vision Not Working?

You might experience that your Wyze camera night vision can partially work but have a blurry image, or it won’t toggle at all.

In most circumstances, the issue is with the night vision mode calibration and camera configuration.

Here is a list of the most common causes of Wyze camera night vision not working:

Now that you know the key problem areas to look out for your Wyze night vision not working, let’s move on to the troubleshooting steps.

How to Fix Wyze Camera Night Vision Not Working?

Tip: You can see if your infrared LEDs work by looking at them through your phone's camera.

Solution 1: Check and Enabling Night Vision

Wyze outdoor camera night vision not working happens most frequently because the night mode is not toggled properly or is set to a different mode.

To fix this, you have to manually check through the app to see if it’s configured to work during nighttime.

Here is how to ensure your Wyze camera night mode is enabled and properly set up:

1. Open the Wyze app and navigate to the live stream of your Wyze camera.
2. Locate the moon icon and tap it to cycle through Night Vision modes (Auto, On, Off).
3. Set Night Vision mode to “On,” save the settings, then close the app.
4. Check if the night vision starts working when the sun goes down.
5. If not, try setting it to Auto in the same way you set it to the “On” mode.
6. Check if the Night Vision responds to changes in lighting.

If, after these steps, your night vision still doesn’t work, proceed to the next solution​​​​​​​​.

Note: You can use motion sensors that turn on an IR light to give you a better picture.

Solution 2: Adjust Infrared Sensitivity

The Wyze camera not working on night vision could happen because the exposure settings or sensitivity are turned too high or too low.

This can cause the image to be blurry or too bright, to the point you can’t distinguish objects and details.

Here are the general steps to adjust your Wyze camera infrared sensitivity settings:

1. Open the Wyze app and access the “Wyze camera” settings.
2. Navigate to “Advanced Settings” or a similar option.
3. Look for “Infrared (IR) Sensitivity” settings.
4. Adjust the sensitivity level, either higher or lower.
5. Save the changes and reboot the Wyze camera.
6. Test Night Vision in various lighting conditions.
7. If the problem persists, experiment with different sensitivity levels until resolved.

Note: If possible, install your Wyze outdoor cameras away from direct sunlight.

Solution 3: Power Cycling the Camera

A possible cause of your Wyze night mode not working is a temporary software error caused by static electricity building up on your camera circuit board.

This can be fixed relatively quickly through restarting your camera.

Here is how to properly power cycle your Wyze camera:

1. Turn off the Wyze camera using the switch at its back.
2. Wait for about 5-10 seconds.
3. Turn the camera back on.
4. Open the Wyze app and check the live stream.
5. Observe if Night Vision is functioning.

Note: If the issue persists, try repeating the power cycling process.

Solution 4: Reposition the Camera

Sometimes, your night vision mode could be working as intended, but the video feed you receive might be blurry.

This could happen if your camera is positioned in a place with high interference or due to other factors.

Here are some tips on how to reposition your Wyze camera for better night mode visibility:

1. Adjust the camera’s position to avoid direct light sources.
2. Ensure it’s not facing glares or streetlights.
3. Check the live stream via the Wyze app.
4. Test out how your camera responds to being placed in different positions.
5. Avoid placing the camera next to strong electrical appliances or power transformers.
6. Clean your camera’s infrared sensors and lens to prevent distortions.

Furthermore, you can always test out different field-of-view settings and viewing angles to see if they improve the image.

Note: Have your security cameras set in a central or visible place to boost deterrence.

Solution 5: Enable IR Lights

Most Wyze cameras that have a night vision mode come with their own set of infrared lights.

In some instances, these might not be enough to fully lighten up your environment or might not be enabled.

Here is how to check your Wyze camera infrared lights for issues:

1. Open the Wyze app and go to the live stream.
2. Access the Settings icon.
3. Navigate to Advanced Settings.
4. Find the ‘Night Vision IR Lights’ option.
5. Ensure it is toggled on.
6. Check the live stream for improvements.

If your WyzeNight Vision is still not working, proceed with the other solutions​​.

Note: You can install aftermarket IR lights to boost the IR strength and distance.

Solution 6: Factory Reset Your Wyze Device

If you have followed the steps above, but you can’t enable the night mode on your device through the app, or it won’t work, you can attempt a factory reset.

This will restore your camera to how it arrived from the factory and revert all settings.

Here are the general steps to factory reset a Wyze camera

1. Remove the Wyze Cam from the Wyze App.
2. Take out any SD card installed in the camera.
3. Hold the Setup Button on the camera for about 15-20 seconds.
4. Wait for the camera to indicate the start of the reset.
5. Check if the LEDs on the camera turn Blue (Red on Wyze Cam V3).
6. Re-add the camera to the Wyze App.
7. Check if Night Vision is working post-reset​​.

Note: A factory reset will erase any saved data or settings, so back them up as needed.

Solution 7: Check For Software Updates

If your Wyze camera has frequent crashes or glitches when night mode is enabled, it might be due to a compatibility issue.

This occurs when your software is outdated, causing limited feature use or instability.

Here is how to properly check for updates of your Wyze app:

1. Take the smartphone or tablet where you installed your Wyze app and log in.
2. Open the Wyze app and select your camera.
3. Access the settings gear icon.
4. Tap on ‘Device Info.’
5. Check for the firmware version.
6. If an update is available, proceed to update the firmware.
7. Allow the camera to update and restart.
8. Verify if Night Vision functionality is restored​​.

Note: Update the Wyze app itself regularly and not just your camera firmware.

Solution 8: Improve Wi-Fi Connectivity

Suppose you receive a live feed during nighttime, but it cuts off or has a high latency and delay.

This could be caused due to a poor WiFi signal reception. To remedy this, you have to manually check your network stability for issues.

Here are some general guidelines to improve your Wyze WiFi connectivity:

1. Check if the Wyze camera is within a good range of your router.
2. Move the camera closer to the router if needed.
3. Ensure there’s no interference from other electronic devices.
4. Restart both your router and camera.
5. Reconnect the camera to your Wi-Fi network.

Additionally, you can try pausing streaming services or disabling the WiFi on unused devices paired to your network.

When you are done with the steps above, check if the Night Vision functionality is improved​​.

Note: Consider using a Wi-Fi extender for better signal strength for your Wyze setup.

Quick Recap

To fix your Wyze camera night vision not working, start by checking if the night mode is toggled on and check the infrared setting.

Next, power cycle your camera and check the WiFi.